TRACEROUTE(1) Traceroute For Linux TRACEROUTE(1) NAME traceroute - print the route packets trace to network host SYNOPSIS traceroute [-46dFITUnreAV] [-f first_ttl] [-g gate,...] [-i device] [-m max_ttl] [-p port] [-s src_addr] [-q nqueries] [-N squeries] [-t tos] [-l flow_label] [-w waittime] [-z sendwait] [-UL] [-D] [-P proto] [--sport=port] [-M method] [-O mod_options] [--mtu] [--back] host [packet_len] traceroute6 [options] tcptraceroute [options] lft [options] DESCRIPTION traceroute tracks the route packets taken from an IP network on their way to a given host. It utilizes the IP protocol's time to live (TTL) field and attempts to elicit an ICMP TIME_EXCEEDED response from each gateway along the path to the host. traceroute6 is equivalent to traceroute -6 tcptraceroute is equivalent to traceroute -T lft , the Layer Four Traceroute, performs a TCP traceroute, like traceroute -T , but attempts to provide compatibility with the original such implementation, also called "lft". The only required parameter is the name or IP address of the destina- tion host . The optional packet_len`gth is the total size of the prob- ing packet (default 60 bytes for IPv4 and 80 for IPv6). The specified size can be ignored in some situations or increased up to a minimal value. This program attempts to trace the route an IP packet would follow to some internet host by launching probe packets with a small ttl (time to live) then listening for an ICMP "time exceeded" reply from a gateway. We start our probes with a ttl of one and increase by one until we get an ICMP "port unreachable" (or TCP reset), which means we got to the "host", or hit a max (which defaults to 30 hops). Three probes (by default) are sent at each ttl setting and a line is printed showing the ttl, address of the gateway and round trip time of each probe. The address can be followed by additional information when requested. If the probe answers come from different gateways, the address of each responding system will be printed. If there is no response within a 5.0 seconds (default), an "*" (asterisk) is printed for that probe. After the trip time, some additional annotation can be printed: !H, !N, or !P (host, network or protocol unreachable), !S (source route failed), !F (fragmentation needed), !X (communication administratively prohibited), !V (host precedence violation), !C (precedence cutoff in effect), or !<num> (ICMP unreachable code <num>). If almost all the probes result in some kind of unreachable, traceroute will give up and exit. We don't want the destination host to process the UDP probe packets, so the destination port is set to an unlikely value (you can change it with the -p flag). There is no such a problem for ICMP or TCP tracer- outing (for TCP we use half-open technique, which prevents our probes to be seen by applications on the destination host). In the modern network environment the traditional traceroute methods can not be always applicable, because of widespread use of firewalls. Such firewalls filter the "unlikely" UDP ports, or even ICMP echoes. To solve this, some additional tracerouting methods are implemented (including tcp), see LIST OF AVAILABLE METHODS below. Such methods try to use particular protocol and source/destination port, in order to bypass firewalls (to be seen by firewalls just as a start of allowed type of a network session). OPTIONS --help Print help info and exit. -4, -6 Explicitly force IPv4 or IPv6 tracerouting. By default, the pro- gram will try to resolve the name given, and choose the appro- priate protocol automatically. If resolving a host name returns both IPv4 and IPv6 addresses, traceroute will use IPv4. -I, --icmp Use ICMP ECHO for probes -T, --tcp Use TCP SYN for probes -d, --debug Enable socket level debugging (when the Linux kernel supports it) -F, --dont-fragment Do not fragment probe packets. (For IPv4 it also sets DF bit, which tells intermediate routers not to fragment remotely as well). Varying the size of the probing packet by the packet_len command line parameter, you can manually obtain information about the MTU of individual network hops. The --mtu option (see below) tries to do this automatically. Note, that non-fragmented features (like -F or --mtu) work prop- erly since the Linux kernel 2.6.22 only. Before that version, IPv6 was always fragmented, IPv4 could use the once the discov- ered final mtu only (from the route cache), which can be less than the actual mtu of a device. -f first_ttl, --first=first_ttl Specifies with what TTL to start. Defaults to 1. -g gateway, --gateway=gateway Tells traceroute to add an IP source routing option to the out- going packet that tells the network to route the packet through the specified gateway (most routers have disabled source routing for security reasons). In general, several gateway's is allowed (comma separated). For IPv6, the form of num,addr,addr... is allowed, where num is a route header type (default is type 2). Note the type 0 route header is now deprecated (rfc5095). -i interface, --interface=interface Specifies the interface through which traceroute should send packets. By default, the interface is selected according to the routing table. -m max_ttl, --max-hops=max_ttl Specifies the maximum number of hops (max time-to-live value) traceroute will probe. The default is 30. -N squeries, --sim-queries=squeries Specifies the number of probe packets sent out simultaneously. Sending several probes concurrently can speed up traceroute con- siderably. The default value is 16. Note that some routers and hosts can use ICMP rate throttling. In such a situation specifying too large number can lead to loss of some responses. -n Do not try to map IP addresses to host names when displaying them. -p port, --port=port For UDP tracing, specifies the destination port base traceroute will use (the destination port number will be incremented by each probe). For ICMP tracing, specifies the initial ICMP sequence value (incremented by each probe too). For TCP and others specifies just the (constant) destination port to connect. When using the tcptraceroute wrapper, -p speci- fies the source port. -t tos, --tos=tos For IPv4, set the Type of Service (TOS) and Precedence value. Useful values are 16 (low delay) and 8 (high throughput). Note that in order to use some TOS precedence values, you have to be super user. For IPv6, set the Traffic Control value. -l flow_label, --flowlabel=flow_label Use specified flow_label for IPv6 packets. -w waittime, --wait=waittime Set the time (in seconds) to wait for a response to a probe (default 5.0 sec). -q nqueries, --queries=nqueries Sets the number of probe packets per hop. The default is 3. -r Bypass the normal routing tables and send directly to a host on an attached network. If the host is not on a directly-attached network, an error is returned. This option can be used to ping a local host through an interface that has no route through it. -s source_addr, --source=source_addr Chooses an alternative source address. Note that you must select the address of one of the interfaces. By default, the address of the outgoing interface is used. -z sendwait, --sendwait=sendwait Minimal time interval between probes (default 0). If the value is more than 10, then it specifies a number in milliseconds, else it is a number of seconds (float point values allowed too). Useful when some routers use rate-limit for ICMP messages. -e, --extensions Show ICMP extensions (rfc4884). The general form is CLASS/TYPE: followed by a hexadecimal dump. The MPLS (rfc4950) is shown parsed, in a form: MPLS:L=label,E=exp_use,S=stack_bottom,T=TTL (more objects separated by / ). -A, --as-path-lookups Perform AS path lookups in routing registries and print results directly after the corresponding addresses. -V, --version Print the version and exit. There is a couple of additional options, intended for an advanced usage (another trace methods etc.): --sport=port Chooses the source port to use. Implies -N 1. Normally source ports (if applicable) are chosen by the system. --fwmark=mark Set the firewall mark for outgoing packets (since the Linux ker- nel 2.6.25). -M method, --module=name Use specified method for traceroute operations. Default tradi- tional udp method has name default, icmp (-I) and tcp (-T) have names icmp and tcp respectively. Method-specific options can be passed by -O . Most methods have their simple shortcuts, (-I means -M icmp, etc). -O option, --options=options Specifies some method-specific option. Several options are sepa- rated by comma (or use several -O on cmdline). Each method may have its own specific options, or many not have them at all. To print information about available options, use -O help. -U, --udp Use UDP to particular destination port for tracerouting (instead of increasing the port per each probe). Default port is 53 (dns). -UL Use UDPLITE for tracerouting (default port is 53). -D, --dccp Use DCCP Requests for probes. -P protocol, --protocol=protocol Use raw packet of specified protocol for tracerouting. Default protocol is 253 (rfc3692). --mtu Discover MTU along the path being traced. Implies -F -N 1. New mtu is printed once in a form of F=NUM at the first probe of a hop which requires such mtu to be reached. (Actually, the corre- spond "frag needed" icmp message normally is sent by the previ- ous hop). Note, that some routers might cache once the seen information on a fragmentation. Thus you can receive the final mtu from a closer hop. Try to specify an unusual tos by -t , this can help for one attempt (then it can be cached there as well). See -F option for more info. --back Print the number of backward hops when it seems different with the forward direction. This number is guessed in assumption that remote hops send reply packets with initial ttl set to either 64, or 128 or 255 (which seems a common practice). It is printed as a negate value in a form of '-NUM' . LIST OF AVAILABLE METHODS In general, a particular traceroute method may have to be chosen by -M name, but most of the methods have their simple cmdline switches (you can see them after the method name, if present). default The traditional, ancient method of tracerouting. Used by default. Probe packets are udp datagrams with so-called "unlikely" destination ports. The "unlikely" port of the first probe is 33434, then for each next probe it is incremented by one. Since the ports are expected to be unused, the destination host normally returns "icmp unreach port" as a final response. (Nobody knows what happens when some application lis- tens for such ports, though). This method is allowed for unprivileged users. icmp -I Most usual method for now, which uses icmp echo packets for probes. If you can ping(8) the destination host, icmp tracerouting is applica- ble as well. This method may be allowed for unprivileged users since the kernel 3.0 (IPv4 only), which supports new dgram icmp (or "ping") sockets. To allow such sockets, sysadmin should provide net/ipv4/ping_group_range sysctl range to match any group of the user. Options: raw Use only raw sockets (the traditional way). This way is tried first by default (for compatibility reasons), then new dgram icmp sockets as fallback. dgram Use only dgram icmp sockets. tcp -T Well-known modern method, intended to bypass firewalls. Uses the constant destination port (default is 80, http). If some filters are present in the network path, then most probably any "unlikely" udp ports (as for default method) or even icmp echoes (as for icmp) are filtered, and whole tracerouting will just stop at such a firewall. To bypass a network filter, we have to use only allowed pro- tocol/port combinations. If we trace for some, say, mailserver, then more likely -T -p 25 can reach it, even when -I can not. This method uses well-known "half-open technique", which prevents applications on the destination host from seeing our probes at all. Normally, a tcp syn is sent. For non-listened ports we receive tcp reset, and all is done. For active listening ports we receive tcp syn+ack, but answer by tcp reset (instead of expected tcp ack), this way the remote tcp session is dropped even without the application ever taking notice. There is a couple of options for tcp method: syn,ack,fin,rst,psh,urg,ece,cwr Sets specified tcp flags for probe packet, in any combination. flags=num Sets the flags field in the tcp header exactly to num. ecn Send syn packet with tcp flags ECE and CWR (for Explicit Conges- tion Notification, rfc3168). sack,timestamps,window_scaling Use the corresponding tcp header option in the outgoing probe packet. sysctl Use current sysctl (/proc/sys/net/*) setting for the tcp header options above and ecn. Always set by default, if nothing else specified. mss=num Use value of num for maxseg tcp header option (when syn). info Print tcp flags of final tcp replies when the target host is reached. Allows to determine whether an application listens the port and other useful things. Default options is syn,sysctl. tcpconn An initial implementation of tcp method, simple using connect(2) call, which does full tcp session opening. Not recommended for normal use, because a destination application is always affected (and can be con- fused). udp -U Use udp datagram with constant destination port (default 53, dns). Intended to bypass firewall as well. Note, that unlike in tcp method, the correspond application on the des- tination host always receive our probes (with random data), and most can easily be confused by them. Most cases it will not respond to our packets though, so we will never see the final hop in the trace. (For- tunately, it seems that at least dns servers replies with something angry). This method is allowed for unprivileged users. udplite -UL Use udplite datagram for probes (with constant destination port, default 53). This method is allowed for unprivileged users. Options: coverage=num Set udplite send coverage to num. dccp -D Use DCCP Request packets for probes (rfc4340). This method uses the same "half-open technique" as used for TCP. The default destination port is 33434. Options: service=num Set DCCP service code to num (default is 1885957735). raw -P proto Send raw packet of protocol proto. No protocol-specific headers are used, just IP header only. Implies -N 1. Options: protocol=proto Use IP protocol proto (default 253). NOTES To speed up work, normally several probes are sent simultaneously. On the other hand, it creates a "storm of packages", especially in the reply direction. Routers can throttle the rate of icmp responses, and some of replies can be lost. To avoid this, decrease the number of simultaneous probes, or even set it to 1 (like in initial traceroute implementation), i.e. -N 1 The final (target) host can drop some of the simultaneous probes, and might even answer only the latest ones. It can lead to extra "looks like expired" hops near the final hop. We use a smart algorithm to auto-detect such a situation, but if it cannot help in your case, just use -N 1 too. For even greater stability you can slow down the program's work by -z option, for example use -z 0.5 for half-second pause between probes. If some hops report nothing for every method, the last chance to obtain something is to use ping -R command (IPv4, and for nearest 8 hops only). SEE ALSO ping(8), ping6(8), tcpdump(8), netstat(8) Traceroute 11 October 2006 TRACEROUTE(1)
Czas wygenerowania: 0.01281 sek.
Created with the man page lookup class by Andrew Collington.
Based on a C man page viewer by Vadim Pavlov
Unicode soft-hyphen fix (as used by RedHat) by Dan Edwards
Some optimisations by Eli Argon
Caching idea and code contribution by James Richardson
Copyright © 2003-2023 Linux.pl
Hosted by Hosting Linux.pl