Opcje wyszukiwania podręcznika man:
Lista stron man zaczynających się od znaku:
A   B   C   D   E   F   G   H   I   J   K   L   M   N   O   P   Q   R   S   T   U   V   W   X   Y   Z   ALPHA   NUM   OTHER   ALL
BUSYBOX(1)                          busybox                         BUSYBOX(1)

       BusyBox - The Swiss Army Knife of Embedded Linux

        busybox <applet> [arguments...]  # or

        <applet> [arguments...]          # if symlinked

       BusyBox combines tiny versions of many common UNIX utilities into a
       single small executable. It provides minimalist replacements for most
       of the utilities you usually find in GNU coreutils, util-linux, etc.
       The utilities in BusyBox generally have fewer options than their full-
       featured GNU cousins; however, the options that are included provide
       the expected functionality and behave very much like their GNU

       BusyBox has been written with size-optimization and limited resources
       in mind.  It is also extremely modular so you can easily include or
       exclude commands (or features) at compile time. This makes it easy to
       customize your embedded systems. To create a working system, just add
       /dev, /etc, and a Linux kernel.  BusyBox provides a fairly complete
       POSIX environment for any small or embedded system.

       BusyBox is extremely configurable.  This allows you to include only the
       components you need, thereby reducing binary size. Run 'make config' or
       'make menuconfig' to select the functionality that you wish to enable.
       Then run 'make' to compile BusyBox using your configuration.

       After the compile has finished, you should use 'make install' to
       install BusyBox. This will install the 'bin/busybox' binary, in the
       target directory specified by CONFIG_PREFIX. CONFIG_PREFIX can be set
       when configuring BusyBox, or you can specify an alternative location at
       install time (i.e., with a command line like 'make
       CONFIG_PREFIX=/tmp/foo install'). If you enabled any applet
       installation scheme (either as symlinks or hardlinks), these will also
       be installed in the location pointed to by CONFIG_PREFIX.

       BusyBox is a multi-call binary.  A multi-call binary is an executable
       program that performs the same job as more than one utility program.
       That means there is just a single BusyBox binary, but that single
       binary acts like a large number of utilities.  This allows BusyBox to
       be smaller since all the built-in utility programs (we call them
       applets) can share code for many common operations.

       You can also invoke BusyBox by issuing a command as an argument on the
       command line.  For example, entering

               /bin/busybox ls

       will also cause BusyBox to behave as 'ls'.

       Of course, adding '/bin/busybox' into every command would be painful.
       So most people will invoke BusyBox using links to the BusyBox binary.

       For example, entering

               ln -s /bin/busybox ls

       will cause BusyBox to behave as 'ls' (if the 'ls' command has been
       compiled into BusyBox).  Generally speaking, you should never need to
       make all these links yourself, as the BusyBox build system will do this
       for you when you run the 'make install' command.

       If you invoke BusyBox with no arguments, it will provide you with a
       list of the applets that have been compiled into your BusyBox binary.

       Most BusyBox applets support the --help argument to provide a terse
       runtime description of their behavior.  If the
       CONFIG_FEATURE_VERBOSE_USAGE option has been enabled, more detailed
       usage information will also be available.

       Currently available applets include:

               [, [[, acpid, adjtimex, ar, arp, arping, ash, awk, basename,
               blockdev, brctl, bunzip2, bzcat, bzip2, cal, cat, chgrp, chmod,
               chown, chroot, chvt, clear, cmp, cp, cpio, cttyhack, cut, date, dc,
               dd, deallocvt, depmod, devmem, df, diff, dirname, dmesg,
               dnsdomainname, dos2unix, du, dumpkmap, dumpleases, echo, egrep, env,
               expand, expr, false, fgrep, find, fold, free, freeramdisk, fstrim,
               ftpget, ftpput, getopt, getty, grep, groups, gunzip, gzip, halt,
               head, hexdump, hostid, hostname, httpd, hwclock, id, ifconfig, init,
               insmod, ionice, ip, ipcalc, kill, killall, klogd, last, less, ln,
               loadfont, loadkmap, logger, login, logname, logread, losetup, ls,
               lsmod, lzcat, lzma, lzop, lzopcat, md5sum, mdev, microcom, mkdir,
               mkfifo, mknod, mkswap, mktemp, modinfo, modprobe, more, mount, mt,
               mv, nameif, nc, netstat, nslookup, od, openvt, patch, pidof, ping,
               ping6, pivot_root, poweroff, printf, ps, pwd, rdate, readlink,
               realpath, reboot, renice, reset, rev, rm, rmdir, rmmod, route, rpm,
               rpm2cpio, run-parts, sed, seq, setkeycodes, setsid, sh, sha1sum,
               sha256sum, sha512sum, sleep, sort, start-stop-daemon, stat, strings,
               stty, swapoff, swapon, switch_root, sync, sysctl, syslogd, tac,
               tail, tar, taskset, tee, telnet, test, tftp, time, timeout, top,
               touch, tr, traceroute, traceroute6, true, tty, udhcpc, udhcpd,
               umount, uname, uncompress, unexpand, uniq, unix2dos, unlzma, unlzop,
               unxz, unzip, uptime, usleep, uudecode, uuencode, vconfig, vi, watch,
               watchdog, wc, wget, which, who, whoami, xargs, xz, xzcat, yes, zcat

           acpid [-df] [-c CONFDIR] [-l LOGFILE] [-a ACTIONFILE] [-M MAPFILE]
           [-e PROC_EVENT_FILE] [-p PIDFILE]

           Listen to ACPI events and spawn specific helpers on event arrival

                   -d      Log to stderr, not log file (implies -f)
                   -f      Run in foreground
                   -c DIR  Config directory [/etc/acpi]
                   -e FILE /proc event file [/proc/acpi/event]
                   -l FILE Log file [/var/log/acpid.log]
                   -p FILE Pid file [/var/run/]
                   -a FILE Action file [/etc/acpid.conf]
                   -M FILE Map file [/etc/]

           Accept and ignore compatibility options -g -m -s -S -v

           adjtimex [-q] [-o OFF] [-f FREQ] [-p TCONST] [-t TICK]

           Read and optionally set system timebase parameters. See adjtimex(2)

                   -q      Quiet
                   -o OFF  Time offset, microseconds
                   -f FREQ Frequency adjust, integer kernel units (65536 is 1ppm)
                           (positive values make clock run faster)
                   -t TICK Microseconds per tick, usually 10000
                   -p TCONST

       ar  ar [-o] [-v] [-p] [-t] [-x] ARCHIVE FILES

           Extract or list FILES from an ar archive

                   -o      Preserve original dates
                   -p      Extract to stdout
                   -t      List
                   -x      Extract
                   -v      Verbose

       arp arp [-vn]     [-H HWTYPE] [-i IF] -a [HOSTNAME] [-v]          [-i
           IF] -d HOSTNAME [pub] [-v] [-H HWTYPE] [-i IF] -s HOSTNAME HWADDR
           [temp] [-v] [-H HWTYPE] [-i IF] -s HOSTNAME HWADDR [netmask MASK]
           pub [-v] [-H HWTYPE] [-i IF] -Ds HOSTNAME IFACE [netmask MASK] pub

           Manipulate ARP cache

                   -a              Display (all) hosts
                   -d              Delete ARP entry
                   -s              Set new entry
                   -v              Verbose
                   -n              Don't resolve names
                   -i IF           Network interface
                   -D              Read HWADDR from IFACE
                   -A,-p AF        Protocol family
                   -H HWTYPE       Hardware address type

           arping [-fqbDUA] [-c CNT] [-w TIMEOUT] [-I IFACE] [-s SRC_IP]

           Send ARP requests/replies

                   -f              Quit on first ARP reply
                   -q              Quiet
                   -b              Keep broadcasting, don't go unicast
                   -D              Duplicated address detection mode
                   -U              Unsolicited ARP mode, update your neighbors
                   -A              ARP answer mode, update your neighbors
                   -c N            Stop after sending N ARP requests
                   -w TIMEOUT      Time to wait for ARP reply, seconds
                   -I IFACE        Interface to use (default eth0)
                   -s SRC_IP       Sender IP address
                   DST_IP          Target IP address

       ash ash [-/+OPTIONS] [-/+o OPT]... [-c 'SCRIPT' [ARG0 [ARGS]] / FILE

           Unix shell interpreter

       awk awk [OPTIONS] [AWK_PROGRAM] [FILE]...

                   -v VAR=VAL      Set variable
                   -F SEP          Use SEP as field separator
                   -f FILE         Read program from FILE
                   -e AWK_PROGRAM

           basename FILE [SUFFIX]

           Strip directory path and .SUFFIX from FILE

           blockdev OPTION BLOCKDEV

                   --setro         Set ro
                   --setrw         Set rw
                   --getro         Get ro
                   --getss         Get sector size
                   --getbsz        Get block size
                   --setbsz BYTES  Set block size
                   --getsz         Get device size in 512-byte sectors
                   --getsize64     Get device size in bytes
                   --flushbufs     Flush buffers
                   --rereadpt      Reread partition table

           brctl COMMAND [BRIDGE [INTERFACE]]

           Manage ethernet bridges


                   addbr BRIDGE            Create BRIDGE
                   delbr BRIDGE            Delete BRIDGE
                   addif BRIDGE IFACE      Add IFACE to BRIDGE
                   delif BRIDGE IFACE      Delete IFACE from BRIDGE

           bunzip2 [-cf] [FILE]...

           Decompress FILEs (or stdin)

                   -c      Write to stdout
                   -f      Force

           bzcat [FILE]...

           Decompress to stdout

           bzip2 [OPTIONS] [FILE]...

           Compress FILEs (or stdin) with bzip2 algorithm

                   -1..9   Compression level
                   -d      Decompress
                   -c      Write to stdout
                   -f      Force

       cal cal [-jy] [[MONTH] YEAR]

           Display a calendar

                   -j      Use julian dates
                   -y      Display the entire year

       cat cat [FILE]...

           Concatenate FILEs and print them to stdout

           chgrp [-RhLHPcvf]... GROUP FILE...

           Change the group membership of each FILE to GROUP

                   -R      Recurse
                   -h      Affect symlinks instead of symlink targets
                   -L      Traverse all symlinks to directories
                   -H      Traverse symlinks on command line only
                   -P      Don't traverse symlinks (default)
                   -c      List changed files
                   -v      Verbose
                   -f      Hide errors

           chmod [-Rcvf] MODE[,MODE]... FILE...

           Each MODE is one or more of the letters ugoa, one of the symbols
           +-= and one or more of the letters rwxst

                   -R      Recurse
                   -c      List changed files
                   -v      List all files
                   -f      Hide errors

           chown [-RhLHPcvf]... OWNER[<.|:>[GROUP]] FILE...

           Change the owner and/or group of each FILE to OWNER and/or GROUP

                   -R      Recurse
                   -h      Affect symlinks instead of symlink targets
                   -L      Traverse all symlinks to directories
                   -H      Traverse symlinks on command line only
                   -P      Don't traverse symlinks (default)
                   -c      List changed files
                   -v      List all files
                   -f      Hide errors

           chroot NEWROOT [PROG ARGS]

           Run PROG with root directory set to NEWROOT

           chvt N

           Change the foreground virtual terminal to /dev/ttyN


           Clear screen

       cmp cmp [-l] [-s] FILE1 [FILE2 [SKIP1 [SKIP2]]]

           Compare FILE1 with FILE2 (or stdin)

                   -l      Write the byte numbers (decimal) and values (octal)
                           for all differing bytes
                   -s      Quiet

       cp  cp [OPTIONS] SOURCE... DEST

           Copy SOURCE(s) to DEST

                   -a      Same as -dpR
                   -R,-r   Recurse
                   -d,-P   Preserve symlinks (default if -R)
                   -L      Follow all symlinks
                   -H      Follow symlinks on command line
                   -p      Preserve file attributes if possible
                   -f      Overwrite
                   -i      Prompt before overwrite
                   -l,-s   Create (sym)links

           cpio [-dmvu] [-F FILE] [-H newc] [-tio] [EXTR_FILE]...

           Extract or list files from a cpio archive, or create an archive
           using file list on stdin

           Main operation mode:

                   -t      List
                   -i      Extract EXTR_FILEs (or all)
                   -o      Create (requires -H newc)
                   -d      Make leading directories
                   -m      Preserve mtime
                   -v      Verbose
                   -u      Overwrite
                   -F FILE Input (-t,-i,-p) or output (-o) file
                   -H newc Archive format

           cttyhack [PROG ARGS]

           Give PROG a controlling tty if possible.  Example for /etc/inittab
           (for busybox init):      ::respawn:/bin/cttyhack /bin/sh Giving
           controlling tty to shell running with PID 1:      $ exec cttyhack
           sh Starting interactive shell from boot shell script:

                   setsid cttyhack sh

       cut cut [OPTIONS] [FILE]...

           Print selected fields from each input FILE to stdout

                   -b LIST Output only bytes from LIST
                   -c LIST Output only characters from LIST
                   -d CHAR Use CHAR instead of tab as the field delimiter
                   -s      Output only the lines containing delimiter
                   -f N    Print only these fields
                   -n      Ignored

           date [OPTIONS] [+FMT] [TIME]

           Display time (using +FMT), or set time

                   [-s,--set] TIME Set time to TIME
                   -u,--utc        Work in UTC (don't convert to local time)
                   -R,--rfc-2822   Output RFC-2822 compliant date string
                   -I[SPEC]        Output ISO-8601 compliant date string
                                   SPEC='date' (default) for date only,
                                   'hours', 'minutes', or 'seconds' for date and
                                   time to the indicated precision
                   -r,--reference FILE     Display last modification time of FILE
                   -d,--date TIME  Display TIME, not 'now'
                   -D FMT          Use FMT for -d TIME conversion

           Recognized TIME formats:

                   YYYY-MM-DD hh:mm[:ss]
                   'date TIME' form accepts MMDDhhmm[[YY]YY][.ss] instead

       dc  dc EXPRESSION...

           Tiny RPN calculator. Operations: +, add, -, sub, *, mul, /, div, %,
           mod, and, or, not, xor, p - print top of the stack (without
           popping), f - print entire stack, o - pop the value and set output
           radix (must be 10, 16, 8 or 2).  Examples: 'dc 2 2 add p' -> 4, 'dc
           8 8 mul 2 2 + / p' -> 16

       dd  dd [if=FILE] [of=FILE] [ibs=N] [obs=N] [bs=N] [count=N] [skip=N]
                [seek=N] [conv=notrunc|noerror|sync|fsync]

           Copy a file with converting and formatting

                   if=FILE         Read from FILE instead of stdin
                   of=FILE         Write to FILE instead of stdout
                   bs=N            Read and write N bytes at a time
                   ibs=N           Read N bytes at a time
                   obs=N           Write N bytes at a time
                   count=N         Copy only N input blocks
                   skip=N          Skip N input blocks
                   seek=N          Skip N output blocks
                   conv=notrunc    Don't truncate output file
                   conv=noerror    Continue after read errors
                   conv=sync       Pad blocks with zeros
                   conv=fsync      Physically write data out before finishing
                   conv=swab       Swap every pair of bytes

           N may be suffixed by c (1), w (2), b (512), kD (1000), k (1024),
           MD, M, GD, G

           deallocvt [N]

           Deallocate unused virtual terminal /dev/ttyN

           depmod [-n] [-b BASE] [VERSION] [MODFILES]...

           Generate modules.dep, alias, and symbols files

                   -b BASE Use BASE/lib/modules/VERSION
                   -n      Dry run: print files to stdout

           devmem ADDRESS [WIDTH [VALUE]]

           Read/write from physical address

                   ADDRESS Address to act upon
                   WIDTH   Width (8/16/...)
                   VALUE   Data to be written

       df  df [-Pkmhai] [-B SIZE] [FILESYSTEM]...

           Print filesystem usage statistics

                   -P      POSIX output format
                   -k      1024-byte blocks (default)
                   -m      1M-byte blocks
                   -h      Human readable (e.g. 1K 243M 2G)
                   -a      Show all filesystems
                   -i      Inodes
                   -B SIZE Blocksize

           diff [-abBdiNqrTstw] [-L LABEL] [-S FILE] [-U LINES] FILE1 FILE2

           Compare files line by line and output the differences between them.
           This implementation supports unified diffs only.

                   -a      Treat all files as text
                   -b      Ignore changes in the amount of whitespace
                   -B      Ignore changes whose lines are all blank
                   -d      Try hard to find a smaller set of changes
                   -i      Ignore case differences
                   -L      Use LABEL instead of the filename in the unified header
                   -N      Treat absent files as empty
                   -q      Output only whether files differ
                   -r      Recurse
                   -S      Start with FILE when comparing directories
                   -T      Make tabs line up by prefixing a tab when necessary
                   -s      Report when two files are the same
                   -t      Expand tabs to spaces in output
                   -U      Output LINES lines of context
                   -w      Ignore all whitespace

           dirname FILENAME

           Strip non-directory suffix from FILENAME

           dmesg [-c] [-n LEVEL] [-s SIZE]

           Print or control the kernel ring buffer

                   -c              Clear ring buffer after printing
                   -n LEVEL        Set console logging level
                   -s SIZE         Buffer size

           dos2unix [-ud] [FILE]

           Convert FILE in-place from DOS to Unix format.  When no file is
           given, use stdin/stdout.

                   -u      dos2unix
                   -d      unix2dos

       du  du [-aHLdclsxhmk] [FILE]...

           Summarize disk space used for each FILE and/or directory

                   -a      Show file sizes too
                   -L      Follow all symlinks
                   -H      Follow symlinks on command line
                   -d N    Limit output to directories (and files with -a) of depth < N
                   -c      Show grand total
                   -l      Count sizes many times if hard linked
                   -s      Display only a total for each argument
                   -x      Skip directories on different filesystems
                   -h      Sizes in human readable format (e.g., 1K 243M 2G)
                   -m      Sizes in megabytes
                   -k      Sizes in kilobytes (default)

           dumpkmap > keymap

           Print a binary keyboard translation table to stdout

           dumpleases [-r|-a] [-f LEASEFILE]

           Display DHCP leases granted by udhcpd

                   -f,--file=FILE  Lease file
                   -r,--remaining  Show remaining time
                   -a,--absolute   Show expiration time

           echo [-neE] [ARG]...

           Print the specified ARGs to stdout

                   -n      Suppress trailing newline
                   -e      Interpret backslash escapes (i.e., \t=tab)
                   -E      Don't interpret backslash escapes (default)

       env env [-iu] [-] [name=value]... [PROG ARGS]

           Print the current environment or run PROG after setting up the
           specified environment

                   -, -i   Start with an empty environment
                   -u      Remove variable from the environment

           expand [-i] [-t N] [FILE]...

           Convert tabs to spaces, writing to stdout

                   -i,--initial    Don't convert tabs after non blanks
                   -t,--tabs=N     Tabstops every N chars

           expr EXPRESSION

           Print the value of EXPRESSION to stdout

           EXPRESSION may be:

                   ARG1 | ARG2     ARG1 if it is neither null nor 0, otherwise ARG2
                   ARG1 & ARG2     ARG1 if neither argument is null or 0, otherwise 0
                   ARG1 < ARG2     1 if ARG1 is less than ARG2, else 0. Similarly:
                   ARG1 <= ARG2
                   ARG1 = ARG2
                   ARG1 != ARG2
                   ARG1 >= ARG2
                   ARG1 > ARG2
                   ARG1 + ARG2     Sum of ARG1 and ARG2. Similarly:
                   ARG1 - ARG2
                   ARG1 * ARG2
                   ARG1 / ARG2
                   ARG1 % ARG2
                   STRING : REGEXP         Anchored pattern match of REGEXP in STRING
                   match STRING REGEXP     Same as STRING : REGEXP
                   substr STRING POS LENGTH Substring of STRING, POS counted from 1
                   index STRING CHARS      Index in STRING where any CHARS is found, or 0
                   length STRING           Length of STRING
                   quote TOKEN             Interpret TOKEN as a string, even if
                                           it is a keyword like 'match' or an
                                           operator like '/'
                   (EXPRESSION)            Value of EXPRESSION

           Beware that many operators need to be escaped or quoted for shells.
           Comparisons are arithmetic if both ARGs are numbers, else
           lexicographical. Pattern matches return the string matched between
           \( and \) or null; if \( and \) are not used, they return the
           number of characters matched or 0.


           Return an exit code of FALSE \fIs0(1)

           find [-HL] [PATH]... [OPTIONS] [ACTIONS]

           Search for files and perform actions on them.  First failed action
           stops processing of current file.  Defaults: PATH is current
           directory, action is '-print'

                   -L,-follow      Follow symlinks
                   -H              ...on command line only
                   -xdev           Don't descend directories on other filesystems
                   -maxdepth N     Descend at most N levels. -maxdepth 0 applies
                                   actions to command line arguments only
                   -mindepth N     Don't act on first N levels
                   -depth          Act on directory *after* traversing it


                   ( ACTIONS )     Group actions for -o / -a
                   ! ACT           Invert ACT's success/failure
                   ACT1 [-a] ACT2  If ACT1 fails, stop, else do ACT2
                   ACT1 -o ACT2    If ACT1 succeeds, stop, else do ACT2
                                   Note: -a has higher priority than -o
                   -name PATTERN   Match file name (w/o directory name) to PATTERN
                   -iname PATTERN  Case insensitive -name
                   -path PATTERN   Match path to PATTERN
                   -ipath PATTERN  Case insensitive -path
                   -regex PATTERN  Match path to regex PATTERN
                   -type X         File type is X (one of: f,d,l,b,c,...)
                   -perm MASK      At least one mask bit (+MASK), all bits (-MASK),
                                   or exactly MASK bits are set in file's mode
                   -mtime DAYS     mtime is greater than (+N), less than (-N),
                                   or exactly N days in the past
                   -mmin MINS      mtime is greater than (+N), less than (-N),
                                   or exactly N minutes in the past
                   -newer FILE     mtime is more recent than FILE's
                   -inum N         File has inode number N
                   -user NAME/ID   File is owned by given user
                   -group NAME/ID  File is owned by given group
                   -size N[bck]    File size is N (c:bytes,k:kbytes,b:512 bytes(def.))
                                   +/-N: file size is bigger/smaller than N
                   -links N        Number of links is greater than (+N), less than (-N),
                                   or exactly N
                   -prune          If current file is directory, don't descend into it
           If none of the following actions is specified, -print is assumed
                   -print          Print file name
                   -print0         Print file name, NUL terminated
                   -exec CMD ARG ; Run CMD with all instances of {} replaced by
                                   file name. Fails if CMD exits with nonzero

           fold [-bs] [-w WIDTH] [FILE]...

           Wrap input lines in each FILE (or stdin), writing to stdout

                   -b      Count bytes rather than columns
                   -s      Break at spaces
                   -w      Use WIDTH columns instead of 80

           free [-b/k/m/g]

           Display the amount of free and used system memory

           freeramdisk DEVICE

           Free all memory used by the specified ramdisk

           fstrim [OPTIONS] MOUNTPOINT

                   -o,--offset=OFFSET      Offset in bytes to discard from
                   -l,--length=LEN         Bytes to discard
                   -m,--minimum=MIN        Minimum extent length
                   -v,--verbose            Print number of discarded bytes


           Download a file via FTP

                   -c,--continue           Continue previous transfer
                   -v,--verbose            Verbose
                   -u,--username USER      Username
                   -p,--password PASS      Password
                   -P,--port NUM           Port


           Upload a file to a FTP server

                   -v,--verbose            Verbose
                   -u,--username USER      Username
                   -p,--password PASS      Password
                   -P,--port NUM           Port

           getopt [OPTIONS] [--] OPTSTRING PARAMS

                   -a,--alternative                Allow long options starting with single -
                   -l,--longoptions=LOPT[,...]     Long options to recognize
                   -n,--name=PROGNAME              The name under which errors are reported
                   -o,--options=OPTSTRING          Short options to recognize
                   -q,--quiet                      No error messages on unrecognized options
                   -Q,--quiet-output               No normal output
                   -s,--shell=SHELL                Set shell quoting conventions
                   -T,--test                       Version test (exits with 4)
                   -u,--unquoted                   Don't quote output


           O=`getopt -l bb: -- ab:c:: "$@"` || exit 1 eval set -- "$O" while
           true; do      case "$1" in      -a)  echo A; shift;;      -b|--bb)
           echo "B:'$2'"; shift 2;;      -c)  case "$2" in           "")  echo
           C; shift 2;;           *)   echo "C:'$2'"; shift 2;;
                     esac;;      --)  shift; break;;      *)   echo Error;
           exit 1;;      esac done


           Open TTY, prompt for login name, then invoke /bin/login

                   -h              Enable hardware RTS/CTS flow control
                   -L              Set CLOCAL (ignore Carrier Detect state)
                   -m              Get baud rate from modem's CONNECT status message
                   -n              Don't prompt for login name
                   -w              Wait for CR or LF before sending /etc/issue
                   -i              Don't display /etc/issue
                   -f ISSUE_FILE   Display ISSUE_FILE instead of /etc/issue
                   -l LOGIN        Invoke LOGIN instead of /bin/login
                   -t SEC          Terminate after SEC if no login name is read
                   -I INITSTR      Send INITSTR before anything else
                   -H HOST         Log HOST into the utmp file as the hostname

           BAUD_RATE of 0 leaves it unchanged

           grep [-HhnlLoqvsriwFEz] [-m N] [-A/B/C N] PATTERN/-e PATTERN.../-f
           FILE [FILE]...

           Search for PATTERN in FILEs (or stdin)

                   -H      Add 'filename:' prefix
                   -h      Do not add 'filename:' prefix
                   -n      Add 'line_no:' prefix
                   -l      Show only names of files that match
                   -L      Show only names of files that don't match
                   -c      Show only count of matching lines
                   -o      Show only the matching part of line
                   -q      Quiet. Return 0 if PATTERN is found, 1 otherwise
                   -v      Select non-matching lines
                   -s      Suppress open and read errors
                   -r      Recurse
                   -i      Ignore case
                   -w      Match whole words only
                   -x      Match whole lines only
                   -F      PATTERN is a literal (not regexp)
                   -E      PATTERN is an extended regexp
                   -z      Input is NUL terminated
                   -m N    Match up to N times per file
                   -A N    Print N lines of trailing context
                   -B N    Print N lines of leading context
                   -C N    Same as '-A N -B N'
                   -e PTRN Pattern to match
                   -f FILE Read pattern from file

           groups [USER]

           Print the group memberships of USER or for the current process

           gunzip [-cft] [FILE]...

           Decompress FILEs (or stdin)

                   -c      Write to stdout
                   -f      Force
                   -t      Test file integrity

           gzip [-cfd] [FILE]...

           Compress FILEs (or stdin)

                   -d      Decompress
                   -c      Write to stdout
                   -f      Force

           halt [-d DELAY] [-n] [-f] [-w]

           Halt the system

                   -d SEC  Delay interval
                   -n      Do not sync
                   -f      Force (don't go through init)
                   -w      Only write a wtmp record

           head [OPTIONS] [FILE]...

           Print first 10 lines of each FILE (or stdin) to stdout.  With more
           than one FILE, precede each with a filename header.

                   -n N[kbm]       Print first N lines
                   -n -N[kbm]      Print all except N last lines
                   -c [-]N[kbm]    Print first N bytes
                   -q              Never print headers
                   -v              Always print headers

           N may be suffixed by k (x1024), b (x512), or m (x1024^2).

           hexdump [-bcCdefnosvx] [FILE]...

           Display FILEs (or stdin) in a user specified format

                   -b              One-byte octal display
                   -c              One-byte character display
                   -C              Canonical hex+ASCII, 16 bytes per line
                   -d              Two-byte decimal display
                   -e FORMAT_STRING
                   -f FORMAT_FILE
                   -n LENGTH       Interpret only LENGTH bytes of input
                   -o              Two-byte octal display
                   -s OFFSET       Skip OFFSET bytes
                   -v              Display all input data
                   -x              Two-byte hexadecimal display


           Print out a unique 32-bit identifier for the machine

           hostname [OPTIONS] [HOSTNAME | -F FILE]

           Get or set hostname or DNS domain name

                   -s      Short
                   -i      Addresses for the hostname
                   -d      DNS domain name
                   -f      Fully qualified domain name
                   -F FILE Use FILE's content as hostname

           httpd [-ifv[v]] [-c CONFFILE] [-p [IP:]PORT] [-u USER[:GRP]] [-r
           REALM] [-h HOME] or httpd -d/-e/-m STRING

           Listen for incoming HTTP requests

                   -i              Inetd mode
                   -f              Don't daemonize
                   -v[v]           Verbose
                   -p [IP:]PORT    Bind to IP:PORT (default *:80)
                   -u USER[:GRP]   Set uid/gid after binding to port
                   -r REALM        Authentication Realm for Basic Authentication
                   -h HOME         Home directory (default .)
                   -c FILE         Configuration file (default {/etc,HOME}/httpd.conf)
                   -m STRING       MD5 crypt STRING
                   -e STRING       HTML encode STRING
                   -d STRING       URL decode STRING

           hwclock [-r|--show] [-s|--hctosys] [-w|--systohc] [-t|--systz]
           [-l|--localtime] [-u|--utc] [-f|--rtc FILE]

           Query and set hardware clock (RTC)

                   -r      Show hardware clock time
                   -s      Set system time from hardware clock
                   -w      Set hardware clock from system time
                   -t      Set in-kernel timezone, correct system time
                           if hardware clock is in local time
                   -u      Assume hardware clock is kept in UTC
                   -l      Assume hardware clock is kept in local time
                   -f FILE Use specified device (e.g. /dev/rtc2)

       id  id [OPTIONS] [USER]

           Print information about USER or the current user

                   -u      User ID
                   -g      Group ID
                   -G      Supplementary group IDs
                   -n      Print names instead of numbers
                   -r      Print real ID instead of effective ID

           ifconfig [-a] interface [address]

           Configure a network interface

                   [add ADDRESS[/PREFIXLEN]]
                   [del ADDRESS[/PREFIXLEN]]
                   [[-]broadcast [ADDRESS]] [[-]pointopoint [ADDRESS]]
                   [netmask ADDRESS] [dstaddr ADDRESS]
                   [outfill NN] [keepalive NN]
                   [hw ether|infiniband ADDRESS] [metric NN] [mtu NN]
                   [[-]trailers] [[-]arp] [[-]allmulti]
                   [multicast] [[-]promisc] [txqueuelen NN] [[-]dynamic]
                   [mem_start NN] [io_addr NN] [irq NN]
                   [up|down] ...


           Init is the first process started during boot. It never exits.  It
           (re)spawns children according to /etc/inittab.

           insmod FILE [SYMBOL=VALUE]...

           Load the specified kernel modules into the kernel

           ionice [-c 1-3] [-n 0-7] [-p PID] [PROG]

           Change I/O priority and class

                   -c      Class. 1:realtime 2:best-effort 3:idle
                   -n      Priority

       ip  ip [OPTIONS] {address | route | link | tunnel | rule} {COMMAND}

           ip [OPTIONS] OBJECT {COMMAND} where OBJECT := {address | route |
           link | tunnel | rule} OPTIONS := { -f[amily] { inet | inet6 | link
           } | -o[neline] }

           ipcalc [OPTIONS] ADDRESS[[/]NETMASK] [NETMASK]

           Calculate IP network settings from a IP address

                   -b,--broadcast  Display calculated broadcast address
                   -n,--network    Display calculated network address
                   -m,--netmask    Display default netmask for IP
                   -p,--prefix     Display the prefix for IP/NETMASK
                   -h,--hostname   Display first resolved host name
                   -s,--silent     Don't ever display error messages

           kill [-l] [-SIG] PID...

           Send a signal (default: TERM) to given PIDs

                   -l      List all signal names and numbers

           killall [-l] [-q] [-SIG] PROCESS_NAME...

           Send a signal (default: TERM) to given processes

                   -l      List all signal names and numbers
                   -q      Don't complain if no processes were killed

           klogd [-c N] [-n]

           Kernel logger

                   -c N    Print to console messages more urgent than prio N (1-8)
                   -n      Run in foreground


           Show listing of the last users that logged into the system

           less [-EMmNh~I?] [FILE]...

           View FILE (or stdin) one screenful at a time

                   -E      Quit once the end of a file is reached
                   -M,-m   Display status line with line numbers
                           and percentage through the file
                   -N      Prefix line number to each line
                   -I      Ignore case in all searches
                   -~      Suppress ~s displayed past EOF

       ln  ln [OPTIONS] TARGET... LINK|DIR

           Create a link LINK or DIR/TARGET to the specified TARGET(s)

                   -s      Make symlinks instead of hardlinks
                   -f      Remove existing destinations
                   -n      Don't dereference symlinks - treat like normal file
                   -b      Make a backup of the target (if exists) before link operation
                   -S suf  Use suffix instead of ~ when making backup files
                   -T      2nd arg must be a DIR
                   -v      Verbose

           loadfont < font

           Load a console font from stdin

           loadkmap < keymap

           Load a binary keyboard translation table from stdin

           logger [OPTIONS] [MESSAGE]

           Write MESSAGE (or stdin) to syslog

                   -s      Log to stderr as well as the system log
                   -t TAG  Log using the specified tag (defaults to user name)
                   -p PRIO Priority (numeric or facility.level pair)

           login [-p] [-h HOST] [[-f] USER]

           Begin a new session on the system

                   -f      Don't authenticate (user already authenticated)
                   -h      Name of the remote host
                   -p      Preserve environment


           Print the name of the current user

           logread [-f]

           Show messages in syslogd's circular buffer

                   -f      Output data as log grows

           losetup [-r] [-o OFS] {-f|LOOPDEV} FILE - associate loop devices
                losetup -d LOOPDEV - disassociate      losetup -a - show
           status      losetup -f - show next free loop device

                   -o OFS  Start OFS bytes into FILE
                   -r      Read-only
                   -f      Show/use next free loop device

       ls  ls [-1AaCxdLHRFplinsehrSXvctu] [-w WIDTH] [FILE]...

           List directory contents

                   -1      One column output
                   -a      Include entries which start with .
                   -A      Like -a, but exclude . and ..
                   -C      List by columns
                   -x      List by lines
                   -d      List directory entries instead of contents
                   -L      Follow symlinks
                   -H      Follow symlinks on command line
                   -R      Recurse
                   -p      Append / to dir entries
                   -F      Append indicator (one of */=@|) to entries
                   -l      Long listing format
                   -i      List inode numbers
                   -n      List numeric UIDs and GIDs instead of names
                   -s      List allocated blocks
                   -e      List full date and time
                   -h      List sizes in human readable format (1K 243M 2G)
                   -r      Sort in reverse order
                   -S      Sort by size
                   -X      Sort by extension
                   -v      Sort by version
                   -c      With -l: sort by ctime
                   -t      With -l: sort by mtime
                   -u      With -l: sort by atime
                   -w N    Assume the terminal is N columns wide
                   --color[={always,never,auto}]   Control coloring


           List the currently loaded kernel modules

           lzcat [FILE]...

           Decompress to stdout

           lzma -d [-cf] [FILE]...

           Decompress FILE (or stdin)

                   -d      Decompress
                   -c      Write to stdout
                   -f      Force

           lzop [-cfvd123456789CF] [FILE]...

                   -1..9   Compression level
                   -d      Decompress
                   -c      Write to stdout
                   -f      Force
                   -v      Verbose
                   -F      Don't store or verify checksum
                   -C      Also write checksum of compressed block

           lzopcat [-vCF] [FILE]...

                   -v      Verbose
                   -F      Don't store or verify checksum

           md5sum [-c[sw]] [FILE]...

           Print or check MD5 checksums

                   -c      Check sums against list in FILEs
                   -s      Don't output anything, status code shows success
                   -w      Warn about improperly formatted checksum lines

           mdev [-s]

           mdev -s is to be run during boot to scan /sys and populate /dev.

           Bare mdev is a kernel hotplug helper. To activate it:      echo
           /sbin/mdev >/proc/sys/kernel/hotplug

           It uses /etc/mdev.conf with lines      [-][ENV=regex;]...DEVNAME
           UID:GID PERM [>|=PATH]|[!] [@|$|*PROG] where DEVNAME is device name
           regex, @major,minor[-minor2], or environment variable regex. A
           common use of the latter is to load modules for hotplugged devices:

                   $MODALIAS=.* 0:0 660 @modprobe "$MODALIAS"

           If /dev/mdev.seq file exists, mdev will wait for its value to match
           $SEQNUM variable. This prevents plug/unplug races.  To activate
           this feature, create empty /dev/mdev.seq at boot.

           If /dev/mdev.log file exists, debug log will be appended to it.

           microcom [-d DELAY] [-t TIMEOUT] [-s SPEED] [-X] TTY

           Copy bytes for stdin to TTY and from TTY to stdout

                   -d      Wait up to DELAY ms for TTY output before sending every
                           next byte to it
                   -t      Exit if both stdin and TTY are silent for TIMEOUT ms
                   -s      Set serial line to SPEED
                   -X      Disable special meaning of NUL and Ctrl-X from stdin

           mkdir [OPTIONS] DIRECTORY...

           Create DIRECTORY

                   -m MODE Mode
                   -p      No error if exists; make parent directories as needed

           mkfifo [-m MODE] NAME

           Create named pipe

                   -m MODE Mode (default a=rw)

           mknod [-m MODE] NAME TYPE MAJOR MINOR

           Create a special file (block, character, or pipe)

                   -m MODE Creation mode (default a=rw)
                   b       Block device
                   c or u  Character device
                   p       Named pipe (MAJOR and MINOR are ignored)

           mkswap [-L LBL] BLOCKDEV [KBYTES]

           Prepare BLOCKDEV to be used as swap partition

                   -L LBL  Label

           mktemp [-dt] [-p DIR] [TEMPLATE]

           Create a temporary file with name based on TEMPLATE and print its
           name.  TEMPLATE must end with XXXXXX (e.g. [/dir/]nameXXXXXX).
           Without TEMPLATE, -t tmp.XXXXXX is assumed.

                   -d      Make directory, not file
                   -q      Fail silently on errors
                   -t      Prepend base directory name to TEMPLATE
                   -p DIR  Use DIR as a base directory (implies -t)
                   -u      Do not create anything; print a name

           Base directory is: -p DIR, else $TMPDIR, else /tmp

           modinfo [-adlp0] [-F keyword] MODULE

                   -a              Shortcut for '-F author'
                   -d              Shortcut for '-F description'
                   -l              Shortcut for '-F license'
                   -p              Shortcut for '-F parm'
                   -F keyword      Keyword to look for
                   -0              Separate output with NULs

           modprobe [-alrqvsDb] MODULE [symbol=value]...

                   -a      Load multiple MODULEs
                   -l      List (MODULE is a pattern)
                   -r      Remove MODULE (stacks) or do autoclean
                   -q      Quiet
                   -v      Verbose
                   -s      Log to syslog
                   -D      Show dependencies
                   -b      Apply blacklist to module names too

           more [FILE]...

           View FILE (or stdin) one screenful at a time

           mount [OPTIONS] [-o OPTS] DEVICE NODE

           Mount a filesystem. Filesystem autodetection requires /proc.

                   -a              Mount all filesystems in fstab
                   -f              Dry run
                   -i              Don't run mount helper
                   -r              Read-only mount
                   -w              Read-write mount (default)
                   -t FSTYPE[,...] Filesystem type(s)
                   -O OPT          Mount only filesystems with option OPT (-a only)
           -o OPT:
                   loop            Ignored (loop devices are autodetected)
                   [a]sync         Writes are [a]synchronous
                   [no]atime       Disable/enable updates to inode access times
                   [no]diratime    Disable/enable atime updates to directories
                   [no]relatime    Disable/enable atime updates relative to modification time
                   [no]dev         (Dis)allow use of special device files
                   [no]exec        (Dis)allow use of executable files
                   [no]suid        (Dis)allow set-user-id-root programs
                   [r]shared       Convert [recursively] to a shared subtree
                   [r]slave        Convert [recursively] to a slave subtree
                   [r]private      Convert [recursively] to a private subtree
                   [un]bindable    Make mount point [un]able to be bind mounted
                   [r]bind         Bind a file or directory [recursively] to another location
                   move            Relocate an existing mount point
                   remount         Remount a mounted filesystem, changing flags
                   ro/rw           Same as -r/-w

           There are filesystem-specific -o flags.

       mt  mt [-f device] opcode value

           Control magnetic tape drive operation

           Available Opcodes:

           bsf bsfm bsr bss datacompression drvbuffer eof eom erase fsf fsfm
           fsr fss load lock mkpart nop offline ras1 ras2 ras3 reset retension
           rewind rewoffline seek setblk setdensity setpart tell unload unlock
           weof wset

       mv  mv [-fin] SOURCE DEST or: mv [-fin] SOURCE... DIRECTORY

           Rename SOURCE to DEST, or move SOURCE(s) to DIRECTORY

                   -f      Don't prompt before overwriting
                   -i      Interactive, prompt before overwrite
                   -n      Don't overwrite an existing file

           nameif [-s] [-c FILE] [IFNAME HWADDR]...

           Rename network interface while it in the down state.  The device
           with address HWADDR is renamed to IFACE.

                   -c FILE Configuration file (default: /etc/mactab)
                   -s      Log to syslog

       nc  nc [-iN] [-wN] [-l] [-p PORT] [-f FILE|IPADDR PORT] [-e PROG]

           Open a pipe to IP:PORT or FILE

                   -l      Listen mode, for inbound connects
                           (use -ll with -e for persistent server)
                   -p PORT Local port
                   -w SEC  Connect timeout
                   -i SEC  Delay interval for lines sent
                   -f FILE Use file (ala /dev/ttyS0) instead of network
                   -e PROG Run PROG after connect

           netstat [-ral] [-tuwx] [-en]

           Display networking information

                   -r      Routing table
                   -a      All sockets
                   -l      Listening sockets
                           Else: connected sockets
                   -t      TCP sockets
                   -u      UDP sockets
                   -w      Raw sockets
                   -x      Unix sockets
                           Else: all socket types
                   -e      Other/more information
                   -n      Don't resolve names

           nslookup [HOST] [SERVER]

           Query the nameserver for the IP address of the given HOST
           optionally using a specified DNS server

       od  od [-abcdfhilovxs] [-t TYPE] [-A RADIX] [-N SIZE] [-j SKIP] [-S
           MINSTR] [-w WIDTH] [FILE]...

           Print FILEs (or stdin) unambiguously, as octal bytes by default

           openvt [-c N] [-sw] [PROG ARGS]

           Start PROG on a new virtual terminal

                   -c N    Use specified VT
                   -s      Switch to the VT
                   -w      Wait for PROG to exit

           patch [OPTIONS] [ORIGFILE [PATCHFILE]]

                   -p,--strip N            Strip N leading components from file names
                   -i,--input DIFF         Read DIFF instead of stdin
                   -R,--reverse            Reverse patch
                   -N,--forward            Ignore already applied patches
                   -E,--remove-empty-files Remove output files if they become empty

           pidof [NAME]...

           List PIDs of all processes with names that match NAMEs

           ping [OPTIONS] HOST

           Send ICMP ECHO_REQUEST packets to network hosts

                   -4,-6           Force IP or IPv6 name resolution
                   -c CNT          Send only CNT pings
                   -s SIZE         Send SIZE data bytes in packets (default:56)
                   -t TTL          Set TTL
                   -I IFACE/IP     Use interface or IP address as source
                   -W SEC          Seconds to wait for the first response (default:10)
                                   (after all -c CNT packets are sent)
                   -w SEC          Seconds until ping exits (default:infinite)
                                   (can exit earlier with -c CNT)
                   -q              Quiet, only displays output at start
                                   and when finished

           ping6 [OPTIONS] HOST

           Send ICMP ECHO_REQUEST packets to network hosts

                   -c CNT          Send only CNT pings
                   -s SIZE         Send SIZE data bytes in packets (default:56)
                   -I IFACE/IP     Use interface or IP address as source
                   -q              Quiet, only displays output at start
                                   and when finished

           pivot_root NEW_ROOT PUT_OLD

           Move the current root file system to PUT_OLD and make NEW_ROOT the
           new root file system

           poweroff [-d DELAY] [-n] [-f]

           Halt and shut off power

                   -d SEC  Delay interval
                   -n      Do not sync
                   -f      Force (don't go through init)

           printf FORMAT [ARG]...

           Format and print ARG(s) according to FORMAT (a-la C printf)

       ps  ps [-o COL1,COL2=HEADER] [-T]

           Show list of processes

                   -o COL1,COL2=HEADER     Select columns for display
                   -T                      Show threads

       pwd pwd

           Print the full filename of the current working directory

           rdate [-sp] HOST

           Get and possibly set the system date/time from a remote HOST

                   -s      Set the system date/time (default)
                   -p      Print the date/time

           readlink [-fnv] FILE

           Display the value of a symlink

                   -f      Canonicalize by following all symlinks
                   -n      Don't add newline
                   -v      Verbose

           realpath FILE...

           Return the absolute pathnames of given FILE

           reboot [-d DELAY] [-n] [-f]

           Reboot the system

                   -d SEC  Delay interval
                   -n      Do not sync
                   -f      Force (don't go through init)

           renice {{-n INCREMENT} | PRIORITY} [[-p | -g | -u] ID...]

           Change scheduling priority for a running process

                   -n      Adjust current nice value (smaller is faster)
                   -p      Process id(s) (default)
                   -g      Process group id(s)
                   -u      Process user name(s) and/or id(s)


           Reset the screen

       rev rev [FILE]...

           Reverse lines of FILE

       rm  rm [-irf] FILE...

           Remove (unlink) FILEs

                   -i      Always prompt before removing
                   -f      Never prompt
                   -R,-r   Recurse

           rmdir [OPTIONS] DIRECTORY...

           Remove DIRECTORY if it is empty

                   -p|--parents    Include parents

           rmmod [-wfa] [MODULE]...

           Unload kernel modules

                   -w      Wait until the module is no longer used
                   -f      Force unload
                   -a      Remove all unused modules (recursively)

           route [{add|del|delete}]

           Edit kernel routing tables

                   -n      Don't resolve names
                   -e      Display other/more information
                   -A inet{6}      Select address family

       rpm rpm -i PACKAGE.rpm; rpm -qp[ildc] PACKAGE.rpm

           Manipulate RPM packages


                   -i      Install package
                   -qp     Query package
                   -qpi    Show information
                   -qpl    List contents
                   -qpd    List documents
                   -qpc    List config files

           rpm2cpio package.rpm

           Output a cpio archive of the rpm file

           run-parts [-a ARG]... [-u UMASK] [--reverse] [--test]
           [--exit-on-error] DIRECTORY

           Run a bunch of scripts in DIRECTORY

                   -a ARG          Pass ARG as argument to scripts
                   -u UMASK        Set UMASK before running scripts
                   --reverse       Reverse execution order
                   --test          Dry run
                   --exit-on-error Exit if a script exits with non-zero

       sed sed [-inrE] [-f FILE]... [-e CMD]... [FILE]...  or: sed [-inrE] CMD

                   -e CMD  Add CMD to sed commands to be executed
                   -f FILE Add FILE contents to sed commands to be executed
                   -i[SFX] Edit files in-place (otherwise sends to stdout)
                           Optionally back files up, appending SFX
                   -n      Suppress automatic printing of pattern space
                   -r,-E   Use extended regex syntax

           If no -e or -f, the first non-option argument is the sed command
           string.  Remaining arguments are input files (stdin if none).

       seq seq [-w] [-s SEP] [FIRST [INC]] LAST

           Print numbers from FIRST to LAST, in steps of INC.  FIRST, INC
           default to 1.

                   -w      Pad to last with leading zeros
                   -s SEP  String separator

           setkeycodes SCANCODE KEYCODE...

           Set entries into the kernel's scancode-to-keycode map, allowing
           unusual keyboards to generate usable keycodes.

           SCANCODE may be either xx or e0xx (hexadecimal), and KEYCODE is
           given in decimal.

           setsid PROG ARGS

           Run PROG in a new session. PROG will have no controlling terminal
           and will not be affected by keyboard signals (Ctrl-C etc).  See
           setsid(2) for details.

       sh  sh [-/+OPTIONS] [-/+o OPT]... [-c 'SCRIPT' [ARG0 [ARGS]] / FILE

           Unix shell interpreter

           sha1sum [-c[sw]] [FILE]...

           Print or check SHA1 checksums

                   -c      Check sums against list in FILEs
                   -s      Don't output anything, status code shows success
                   -w      Warn about improperly formatted checksum lines

           sha256sum [-c[sw]] [FILE]...

           Print or check SHA256 checksums

                   -c      Check sums against list in FILEs
                   -s      Don't output anything, status code shows success
                   -w      Warn about improperly formatted checksum lines

           sha512sum [-c[sw]] [FILE]...

           Print or check SHA512 checksums

                   -c      Check sums against list in FILEs
                   -s      Don't output anything, status code shows success
                   -w      Warn about improperly formatted checksum lines

           sleep [N]...

           Pause for a time equal to the total of the args given, where each
           arg can have an optional suffix of (s)econds, (m)inutes, (h)ours,
           or (d)ays

           sort [-nrugMcszbdfimSTokt] [-o FILE] [-k
           start[.offset][opts][,end[.offset][opts]] [-t CHAR] [FILE]...

           Sort lines of text

                   -b      Ignore leading blanks
                   -c      Check whether input is sorted
                   -d      Dictionary order (blank or alphanumeric only)
                   -f      Ignore case
                   -g      General numerical sort
                   -i      Ignore unprintable characters
                   -k      Sort key
                   -M      Sort month
                   -n      Sort numbers
                   -o      Output to file
                   -k      Sort by key
                   -t CHAR Key separator
                   -r      Reverse sort order
                   -s      Stable (don't sort ties alphabetically)
                   -u      Suppress duplicate lines
                   -z      Lines are terminated by NUL, not newline
                   -mST    Ignored for GNU compatibility

           start-stop-daemon [OPTIONS] [-S|-K] ... [-- ARGS...]

           Search for matching processes, and then -K: stop all matching
           processes.  -S: start a process unless a matching process is found.

           Process matching:

                   -u,--user USERNAME|UID  Match only this user's processes
                   -n,--name NAME          Match processes with NAME
                                           in comm field in /proc/PID/stat
                   -x,--exec EXECUTABLE    Match processes with this command
                                           in /proc/PID/{exe,cmdline}
                   -p,--pidfile FILE       Match a process with PID from the file
                   All specified conditions must match
           -S only:
                   -x,--exec EXECUTABLE    Program to run
                   -a,--startas NAME       Zeroth argument
                   -b,--background         Background
                   -N,--nicelevel N        Change nice level
                   -c,--chuid USER[:[GRP]] Change to user/group
                   -m,--make-pidfile       Write PID to the pidfile specified by -p
           -K only:
                   -s,--signal SIG         Signal to send
                   -t,--test               Match only, exit with 0 if a process is found

                   -o,--oknodo             Exit with status 0 if nothing is done
                   -v,--verbose            Verbose
                   -q,--quiet              Quiet

           stat [OPTIONS] FILE...

           Display file (default) or filesystem status

                   -c fmt  Use the specified format
                   -f      Display filesystem status
                   -L      Follow links
                   -t      Display info in terse form

           Valid format sequences for files:

            %a     Access rights in octal
            %A     Access rights in human readable form
            %b     Number of blocks allocated (see %B)
            %B     The size in bytes of each block reported by %b
            %d     Device number in decimal
            %D     Device number in hex
            %f     Raw mode in hex
            %F     File type
            %g     Group ID of owner
            %G     Group name of owner
            %h     Number of hard links
            %i     Inode number
            %n     File name
            %N     File name, with -> TARGET if symlink
            %o     I/O block size
            %s     Total size, in bytes
            %t     Major device type in hex
            %T     Minor device type in hex
            %u     User ID of owner
            %U     User name of owner
            %x     Time of last access
            %X     Time of last access as seconds since Epoch
            %y     Time of last modification
            %Y     Time of last modification as seconds since Epoch
            %z     Time of last change
            %Z     Time of last change as seconds since Epoch

           Valid format sequences for file systems:

            %a     Free blocks available to non-superuser
            %b     Total data blocks in file system
            %c     Total file nodes in file system
            %d     Free file nodes in file system
            %f     Free blocks in file system
            %i     File System ID in hex
            %l     Maximum length of filenames
            %n     File name
            %s     Block size (for faster transfer)
            %S     Fundamental block size (for block counts)
            %t     Type in hex
            %T     Type in human readable form

           strings [-afo] [-n LEN] [FILE]...

           Display printable strings in a binary file

                   -a      Scan whole file (default)
                   -f      Precede strings with filenames
                   -n LEN  At least LEN characters form a string (default 4)
                   -o      Precede strings with decimal offsets

           stty [-a|g] [-F DEVICE] [SETTING]...

           Without arguments, prints baud rate, line discipline, and
           deviations from stty sane

                   -F DEVICE       Open device instead of stdin
                   -a              Print all current settings in human-readable form
                   -g              Print in stty-readable form
                   [SETTING]       See manpage

           swapoff [-a] [DEVICE]

           Stop swapping on DEVICE

                   -a      Stop swapping on all swap devices

           swapon [-a] [DEVICE]

           Start swapping on DEVICE

                   -a      Start swapping on all swap devices

           switch_root [-c /dev/console] NEW_ROOT NEW_INIT [ARGS]

           Free initramfs and switch to another root fs:

           chroot to NEW_ROOT, delete all in /, move NEW_ROOT to /, execute
           NEW_INIT. PID must be 1. NEW_ROOT must be a mountpoint.

                   -c DEV  Reopen stdio to DEV after switch


           Write all buffered blocks to disk

           sysctl [OPTIONS] [KEY[=VALUE]]...

           Show/set kernel parameters

                   -e      Don't warn about unknown keys
                   -n      Don't show key names
                   -a      Show all values
                   -w      Set values
                   -p FILE Set values from FILE (default /etc/sysctl.conf)
                   -q      Set values silently

           syslogd [OPTIONS]

           System logging utility (this version of syslogd ignores

                   -n              Run in foreground
                   -O FILE         Log to FILE (default:/var/log/messages)
                   -l N            Log only messages more urgent than prio N (1-8)
                   -S              Smaller output
                   -R HOST[:PORT]  Log to HOST:PORT (default PORT:514)
                   -L              Log locally and via network (default is network only if -R)
                   -C[size_kb]     Log to shared mem buffer (use logread to read it)

       tac tac [FILE]...

           Concatenate FILEs and print them in reverse

           tail [OPTIONS] [FILE]...

           Print last 10 lines of each FILE (or stdin) to stdout.  With more
           than one FILE, precede each with a filename header.

                   -f              Print data as file grows
                   -s SECONDS      Wait SECONDS between reads with -f
                   -n N[kbm]       Print last N lines
                   -n +N[kbm]      Start on Nth line and print the rest
                   -c [+]N[kbm]    Print last N bytes
                   -q              Never print headers
                   -v              Always print headers

           N may be suffixed by k (x1024), b (x512), or m (x1024^2).

       tar tar -[cxtZzJjahmvO] [-f TARFILE] [-C DIR] [FILE]...

           Create, extract, or list files from a tar file


                   c       Create
                   x       Extract
                   t       List
                   f       Name of TARFILE ('-' for stdin/out)
                   C       Change to DIR before operation
                   v       Verbose
                   Z       (De)compress using compress
                   z       (De)compress using gzip
                   J       (De)compress using xz
                   j       (De)compress using bzip2
                   a       (De)compress using lzma
                   O       Extract to stdout
                   h       Follow symlinks
                   m       Don't restore mtime

           taskset [-p] [MASK] [PID | PROG ARGS]

           Set or get CPU affinity

                   -p      Operate on an existing PID

       tee tee [-ai] [FILE]...

           Copy stdin to each FILE, and also to stdout

                   -a      Append to the given FILEs, don't overwrite
                   -i      Ignore interrupt signals (SIGINT)

           telnet [-a] [-l USER] HOST [PORT]

           Connect to telnet server

                   -a      Automatic login with $USER variable
                   -l USER Automatic login as USER

           test EXPRESSION ]

           Check file types, compare values etc. Return a 0/1 exit code
           depending on logical value of EXPRESSION

           tftp [OPTIONS] HOST [PORT]

           Transfer a file from/to tftp server

                   -l FILE Local FILE
                   -r FILE Remote FILE
                   -g      Get file
                   -p      Put file
                   -b SIZE Transfer blocks of SIZE octets

           time [-v] PROG ARGS

           Run PROG, display resource usage when it exits

                   -v      Verbose

           timeout [-t SECS] [-s SIG] PROG ARGS

           Runs PROG. Sends SIG to it if it is not gone in SECS seconds.
           Defaults: SECS: 10, SIG: TERM.

       top top [-b] [-nCOUNT] [-dSECONDS]

           Provide a view of process activity in real time.  Read the status
           of all processes from /proc each SECONDS and display a screenful of
           them.  Keys:

                   N/M/P/T: sort by pid/mem/cpu/time
                   R: reverse sort
                   H: toggle threads
                   Q,^C: exit


                   -b      Batch mode
                   -n N    Exit after N iterations
                   -d N    Delay between updates

           touch [-c] [-d DATE] [-t DATE] [-r FILE] FILE...

           Update the last-modified date on the given FILE[s]

                   -c      Don't create files
                   -h      Don't follow links
                   -d DT   Date/time to use
                   -t DT   Date/time to use
                   -r FILE Use FILE's date/time

       tr  tr [-cds] STRING1 [STRING2]

           Translate, squeeze, or delete characters from stdin, writing to

                   -c      Take complement of STRING1
                   -d      Delete input characters coded STRING1
                   -s      Squeeze multiple output characters of STRING2 into one character

           traceroute [-46FIldnrv] [-f 1ST_TTL] [-m MAXTTL] [-p PORT] [-q
           PROBES]      [-s SRC_IP] [-t TOS] [-w WAIT_SEC] [-g GATEWAY] [-i
           IFACE]      [-z PAUSE_MSEC] HOST [BYTES]

           Trace the route to HOST

                   -4,-6   Force IP or IPv6 name resolution
                   -F      Set the don't fragment bit
                   -I      Use ICMP ECHO instead of UDP datagrams
                   -l      Display the TTL value of the returned packet
                   -d      Set SO_DEBUG options to socket
                   -n      Print numeric addresses
                   -r      Bypass routing tables, send directly to HOST
                   -v      Verbose
                   -m      Max time-to-live (max number of hops)
                   -p      Base UDP port number used in probes
                           (default 33434)
                   -q      Number of probes per TTL (default 3)
                   -s      IP address to use as the source address
                   -t      Type-of-service in probe packets (default 0)
                   -w      Time in seconds to wait for a response (default 3)
                   -g      Loose source route gateway (8 max)

           traceroute6 [-dnrv] [-m MAXTTL] [-p PORT] [-q PROBES]      [-s
           SRC_IP] [-t TOS] [-w WAIT_SEC] [-i IFACE]      HOST [BYTES]

           Trace the route to HOST

                   -d      Set SO_DEBUG options to socket
                   -n      Print numeric addresses
                   -r      Bypass routing tables, send directly to HOST
                   -v      Verbose
                   -m      Max time-to-live (max number of hops)
                   -p      Base UDP port number used in probes
                           (default is 33434)
                   -q      Number of probes per TTL (default 3)
                   -s      IP address to use as the source address
                   -t      Type-of-service in probe packets (default 0)
                   -w      Time in seconds to wait for a response (default 3)


           Return an exit code of TRUE \fIs0(0)

       tty tty

           Print file name of stdin's terminal

                   -s      Print nothing, only return exit status

           udhcpc [-fbqaRB] [-t N] [-T SEC] [-A SEC/-n]      [-i IFACE] [-s
           PROG] [-p PIDFILE]      [-oC] [-r IP] [-V VENDOR] [-F NAME] [-x
           OPT:VAL]... [-O OPT]...

                   -i,--interface IFACE    Interface to use (default eth0)
                   -s,--script PROG        Run PROG at DHCP events (default /etc/udhcpc/default.script)
                   -p,--pidfile FILE       Create pidfile
                   -B,--broadcast          Request broadcast replies
                   -t,--retries N          Send up to N discover packets (default 3)
                   -T,--timeout SEC        Pause between packets (default 3)
                   -A,--tryagain SEC       Wait if lease is not obtained (default 20)
                   -n,--now                Exit if lease is not obtained
                   -q,--quit               Exit after obtaining lease
                   -R,--release            Release IP on exit
                   -f,--foreground         Run in foreground
                   -b,--background         Background if lease is not obtained
                   -S,--syslog             Log to syslog too
                   -a,--arping             Use arping to validate offered address
                   -r,--request IP         Request this IP address
                   -o,--no-default-options Don't request any options (unless -O is given)
                   -O,--request-option OPT Request option OPT from server (cumulative)
                   -x OPT:VAL              Include option OPT in sent packets (cumulative)
                                           Examples of string, numeric, and hex byte opts:
                                           -x hostname:bbox - option 12
                                           -x lease:3600 - option 51 (lease time)
                                           -x 0x3d:0100BEEFC0FFEE - option 61 (client id)
                   -F,--fqdn NAME          Ask server to update DNS mapping for NAME
                   -V,--vendorclass VENDOR Vendor identifier (default 'udhcp VERSION')
                   -C,--clientid-none      Don't send MAC as client identifier

                   USR1    Renew lease
                   USR2    Release lease

           udhcpd [-fS] [-I ADDR] [CONFFILE]

           DHCP server

                   -f      Run in foreground
                   -S      Log to syslog too
                   -I ADDR Local address


           Unmount file systems

                   -a      Unmount all file systems
                   -r      Try to remount devices as read-only if mount is busy
                   -l      Lazy umount (detach filesystem)
                   -f      Force umount (i.e., unreachable NFS server)
                   -D      Don't free loop device even if it has been used

           uname [-amnrspv]

           Print system information

                   -a      Print all
                   -m      The machine (hardware) type
                   -n      Hostname
                   -r      OS release
                   -s      OS name (default)
                   -p      Processor type
                   -v      OS version

           uncompress [-cf] [FILE]...

           Decompress .Z file[s]

                   -c      Write to stdout
                   -f      Overwrite

           unexpand [-fa][-t N] [FILE]...

           Convert spaces to tabs, writing to stdout

                   -a,--all        Convert all blanks
                   -f,--first-only Convert only leading blanks
                   -t,--tabs=N     Tabstops every N chars

           uniq [-cdu][-f,s,w N] [INPUT [OUTPUT]]

           Discard duplicate lines

                   -c      Prefix lines by the number of occurrences
                   -d      Only print duplicate lines
                   -u      Only print unique lines
                   -f N    Skip first N fields
                   -s N    Skip first N chars (after any skipped fields)
                   -w N    Compare N characters in line

           unix2dos [-ud] [FILE]

           Convert FILE in-place from Unix to DOS format.  When no file is
           given, use stdin/stdout.

                   -u      dos2unix
                   -d      unix2dos

           unlzma [-cf] [FILE]...

           Decompress FILE (or stdin)

                   -c      Write to stdout
                   -f      Force

           unlzop [-cfvCF] [FILE]...

                   -c      Write to stdout
                   -f      Force
                   -v      Verbose
                   -F      Don't store or verify checksum

           unxz [-cf] [FILE]...

           Decompress FILE (or stdin)

                   -c      Write to stdout
                   -f      Force

           unzip [-lnopq] FILE[.zip] [FILE]... [-x FILE...] [-d DIR]

           Extract FILEs from ZIP archive

                   -l      List contents (with -q for short form)
                   -n      Never overwrite files (default: ask)
                   -o      Overwrite
                   -p      Print to stdout
                   -q      Quiet
                   -x FILE Exclude FILEs
                   -d DIR  Extract into DIR


           Display the time since the last boot

           usleep N

           Pause for N microseconds

           uudecode [-o OUTFILE] [INFILE]

           Uudecode a file Finds OUTFILE in uuencoded source unless -o is

           uuencode [-m] [FILE] STORED_FILENAME

           Uuencode FILE (or stdin) to stdout

                   -m      Use base64 encoding per RFC1521

           vconfig COMMAND [OPTIONS]

           Create and remove virtual ethernet devices

                   add             IFACE VLAN_ID
                   rem             VLAN_NAME
                   set_flag        IFACE 0|1 VLAN_QOS
                   set_egress_map  VLAN_NAME SKB_PRIO VLAN_QOS
                   set_ingress_map VLAN_NAME SKB_PRIO VLAN_QOS
                   set_name_type   NAME_TYPE

       vi  vi [OPTIONS] [FILE]...

           Edit FILE

                   -c CMD  Initial command to run ($EXINIT also available)
                   -R      Read-only
                   -H      List available features

           watch [-n SEC] [-t] PROG ARGS

           Run PROG periodically

                   -n      Loop period in seconds (default 2)
                   -t      Don't print header

           watchdog [-t N[ms]] [-T N[ms]] [-F] DEV

           Periodically write to watchdog device DEV

                   -T N    Reboot after N seconds if not reset (default 60)
                   -t N    Reset every N seconds (default 30)
                   -F      Run in foreground

           Use 500ms to specify period in milliseconds

       wc  wc [-cmlwL] [FILE]...

           Count lines, words, and bytes for each FILE (or stdin)

                   -c      Count bytes
                   -m      Count characters
                   -l      Count newlines
                   -w      Count words
                   -L      Print longest line length

           wget [-c|--continue] [-s|--spider] [-q|--quiet]
           [-O|--output-document FILE]      [--header 'header: value']
           [-Y|--proxy on/off] [-P DIR]      [-U|--user-agent AGENT] URL...

           Retrieve files via HTTP or FTP

                   -s      Spider mode - only check file existence
                   -c      Continue retrieval of aborted transfer
                   -q      Quiet
                   -P DIR  Save to DIR (default .)
                   -O FILE Save to FILE ('-' for stdout)
                   -U STR  Use STR for User-Agent header
                   -Y      Use proxy ('on' or 'off')

           which [COMMAND]...

           Locate a COMMAND

       who who [-a]

           Show who is logged on

                   -a      Show all
                   -H      Print column headers


           Print the user name associated with the current effective user id

           xargs [OPTIONS] [PROG ARGS]

           Run PROG on every item given by stdin

                   -p      Ask user whether to run each command
                   -r      Don't run command if input is empty
                   -0      Input is separated by NUL characters
                   -t      Print the command on stderr before execution
                   -e[STR] STR stops input processing
                   -n N    Pass no more than N args to PROG
                   -s N    Pass command line of no more than N bytes
                   -x      Exit if size is exceeded

       xz  xz -d [-cf] [FILE]...

           Decompress FILE (or stdin)

                   -d      Decompress
                   -c      Write to stdout
                   -f      Force

           xzcat [FILE]...

           Decompress to stdout

       yes yes [STRING]

           Repeatedly output a line with STRING, or 'y'

           zcat [FILE]...

           Decompress to stdout

       GNU Libc (glibc) uses the Name Service Switch (NSS) to configure the
       behavior of the C library for the local environment, and to configure
       how it reads system data, such as passwords and group information.
       This is implemented using an /etc/nsswitch.conf configuration file, and
       using one or more of the /lib/libnss_* libraries.  BusyBox tries to
       avoid using any libc calls that make use of NSS.  Some applets however,
       such as login and su, will use libc functions that require NSS.

       If you enable CONFIG_USE_BB_PWD_GRP, BusyBox will use internal
       functions to directly access the /etc/passwd, /etc/group, and
       /etc/shadow files without using NSS.  This may allow you to run your
       system without the need for installing any of the NSS configuration
       files and libraries.

       When used with glibc, the BusyBox 'networking' applets will similarly
       require that you install at least some of the glibc NSS stuff (in
       particular, /etc/nsswitch.conf, /lib/libnss_dns*, /lib/libnss_files*,
       and /lib/libresolv*).

       Shameless Plug: As an alternative, one could use a C library such as
       uClibc.  In addition to making your system significantly smaller,
       uClibc does not require the use of any NSS support files or libraries.

       Denis Vlasenko <>

       The following people have contributed code to BusyBox whether they know
       it or not.  If you have written code included in BusyBox, you should
       probably be listed here so you can obtain your bit of eternal glory.
       If you should be listed here, or the description of what you have done
       needs more detail, or is incorrect, please send in an update.

       Emanuele Aina <>

       Erik Andersen <>

           Tons of new stuff, major rewrite of most of the
           core apps, tons of new apps as noted in header files.
           Lots of tedious effort writing these boring docs that
           nobody is going to actually read.

       Laurence Anderson <>

           rpm2cpio, unzip, get_header_cpio, read_gz interface, rpm

       Jeff Angielski <>

           ftpput, ftpget

       Edward Betts <>

           expr, hostid, logname, whoami

       John Beppu <>

           du, nslookup, sort

       Brian Candler <>


       Randolph Chung <>

           fbset, ping, hostname

       Dave Cinege <>

           more(v2), makedevs, dutmp, modularization, auto links file,
           various fixes, Linux Router Project maintenance

       Jordan Crouse <>


       Magnus Damm <>

           tftp client insmod powerpc support

       Larry Doolittle <>

           pristine source directory compilation, lots of patches and fixes.

       Glenn Engel <>


       Gennady Feldman <>

           Sysklogd (single threaded syslogd, IPC Circular buffer support,
           logread), various fixes.

       Karl M. Hegbloom <>

           cp_mv.c, the test suite, various fixes to utility.c, &c.

       Daniel Jacobowitz <>


       Matt Kraai <>

           documentation, bugfixes, test suite

       Stephan Linz <>

           ipcalc, Red Hat equivalence

       John Lombardo <>


       Glenn McGrath <>

           Common unarchiving code and unarchiving applets, ifupdown, ftpgetput,
           nameif, sed, patch, fold, install, uudecode.
           Various bugfixes, review and apply numerous patches.

       Manuel Novoa III <>

           cat, head, mkfifo, mknod, rmdir, sleep, tee, tty, uniq, usleep, wc, yes,
           mesg, vconfig, make_directory, parse_mode, dirname, mode_string,
           get_last_path_component, simplify_path, and a number trivial libbb routines

           also bug fixes, partial rewrites, and size optimizations in
           ash, basename, cal, cmp, cp, df, du, echo, env, ln, logname, md5sum, mkdir,
           mv, realpath, rm, sort, tail, touch, uname, watch, arith, human_readable,
           interface, dutmp, ifconfig, route

       Vladimir Oleynik <>

           cmdedit; xargs(current), httpd(current);
           ports: ash, crond, fdisk, inetd, stty, traceroute, top;
           locale, various fixes
           and irreconcilable critic of everything not perfect.

       Bruce Perens <>

           Original author of BusyBox in 1995, 1996. Some of his code can
           still be found hiding here and there...

       Tim Riker <>

           bug fixes, member of fan club

       Kent Robotti <>

           reset, tons and tons of bug reports and patches.

       Chip Rosenthal <>, <>

           wget - Contributed by permission of Covad Communications

       Pavel Roskin <>

           Lots of bugs fixes and patches.

       Gyepi Sam <>

           Remote logging feature for syslogd

       Linus Torvalds <>

           mkswap, fsck.minix, mkfs.minix

       Mark Whitley <>

           grep, sed, cut, xargs(previous),
           style-guide, new-applet-HOWTO, bug fixes, etc.

       Charles P. Wright <>

           gzip, mini-netcat(nc)

       Enrique Zanardi <>

           tarcat (since removed), loadkmap, various fixes, Debian maintenance

       Tito Ragusa <>

           devfsd and size optimizations in strings, openvt and deallocvt.

       Paul Fox <>

           vi editing mode for ash, various other patches/fixes

       Roberto A. Foglietta <>

           port: dnsd

       Bernhard Reutner-Fischer <>


       Mike Frysinger <>

           initial e2fsprogs, printenv, setarch, sum, misc

       Jie Zhang <>

           fixed two bugs in msh and hush (exitcode of killed processes)

version 1.22.1                    2018-08-03                        BUSYBOX(1)

Czas wygenerowania: 0.00094 sek.

Created with the man page lookup class by Andrew Collington.
Based on a C man page viewer by Vadim Pavlov
Unicode soft-hyphen fix (as used by RedHat) by Dan Edwards
Some optimisations by Eli Argon
Caching idea and code contribution by James Richardson

Copyright © 2003-2023
Hosted by Hosting