BRIDGE(8) Linux BRIDGE(8)
NAME
bridge - show / manipulate bridge addresses and devices
SYNOPSIS
bridge [ OPTIONS ] OBJECT { COMMAND | help }
OBJECT := { link | fdb | mdb | vlan | monitor }
OPTIONS := { -V[ersion] | -s[tatistics] }
bridge link set dev DEV [ cost COST ] [ priority PRIO ] [ state
STATE] [ guard { on | off } ] [ hairpin { on | off } ] [
fastleave { on | off } ] [ root_block { on | off } ] [ learning
{ on | off } ] [ flood { on | off } ] [ hwmode { vepa | veb } ]
bridge link [ show ] [ dev DEV ]
bridge fdb { add | append | del } LLADDR dev DEV { local | temp } {
self } { embedded } { router } [ dst IPADDR ] [ vni VNI ] [
port PORT ] [ via DEVICE ]
bridge fdb [ show ] [ dev DEV ]
bridge mdb { add | del } dev DEV port PORT grp GROUP [ permanent | temp
]
bridge mdb show [ dev DEV ]
bridge vlan { add | del } dev DEV vid VID [ pvid ] [ untagged ] [ self
] [ master ]
bridge vlan [ show ] [ dev DEV ]
bridge monitor [ all | neigh | link | mdb ]
OPTIONS
-V, -Version
print the version of the bridge utility and exit.
-s, -stats, -statistics
output more information. If this option is given multiple
times, the amount of information increases. As a rule, the
information is statistics or some time values.
BRIDGE - COMMAND SYNTAX
OBJECT
link - Bridge port.
fdb - Forwarding Database entry.
mdb - Multicast group database entry.
vlan - VLAN filter list.
COMMAND
Specifies the action to perform on the object. The set of possible
actions depends on the object type. As a rule, it is possible to add,
delete and show (or list ) objects, but some objects do not allow all
of these operations or have some additional commands. The help command
is available for all objects. It prints out a list of available com-
mands and argument syntax conventions.
If no command is given, some default command is assumed. Usually it is
list or, if the objects of this class cannot be listed, help.
bridge link - bridge port
link objects correspond to the port devices of the bridge.
The corresponding commands set and display port status and bridge spe-
cific attributes.
bridge link set - set bridge specific attributes on a port
dev NAME
interface name of the bridge port
cost COST
the STP path cost of the specified port.
priority PRIO
the STP port priority. The priority value is an unsigned 8-bit
quantity (number between 0 and 255). This metric is used in the
designated port an droot port selectio algorithms.
state STATE
the operation state of the port. This is primarily used by user
space STP/RSTP implementation. The following is a list of valid
values:
0 - port is DISABLED. Make this port completely inactive.
1 - STP LISTENING state. Only valid if STP is enabled on the
brige. In this state the port for list for STP BPDUs and drop
all other traffic.
2 - STP LEARNING state. Only valid if STP is enabled on the
bridge. In this state the port will accept traffic only for the
purpose of updating MAC adress tables.
3 - STP FORWARDING state. Port is fully active.
4 - STP BLOCKING state. Only valid if STP is enabled on the
bridge. This state is used during the STP election process. In
this state, port will only process STP BPDUs.
guard on or guard off
Controls whether STP BPUDs will be processed by the bridge port.
By default, the flag is turned off allowed BPDU processing.
Turning this flag on will cause the port to stop processing STP
BPDUs.
hairpin on or hairpin off
Controls whether traffic may be send back out of the port on
which it was received. By default, this flag is turned off and
the bridge will not forward traffic back out of the receiving
port.
fastleave on or fastleave off
This flag allows the bridge to immediately stop multicast traf-
fic on a port that receives IGMP Leave message. It is only used
with IGMP snooping is enabled on the bridge. By default the
flag is off.
root_block on or root_block off
Controls whether a given port is allowed to become root port or
not. Only used when STP is enabled on the bridge. By default
the flag is off.
learning on or learning off
Controls whether a given port will learn MAC addresses from
received traffic or not. If learning if off, the bridge will
end up flooding any traffic for which it has no FDB entry. By
default this flag is on.
flooding on or flooding off
Controls whether a given port will flood unicast traffic for
which there is no FDB entry. By default this flag is on.
hwmode Some network interface cards support HW bridge functionality and
they may be configured in different modes. Currently support
modes are:
vepa - Data sent between HW ports is sent on the wire to the
external switch.
veb - bridging happens in hardware.
bridge link show - list bridge port configuration.
This command displays the current bridge port configuration and flags.
bridge fdb - forwarding database management
fdb objects contain known Ethernet addresses on a link.
The corresponding commands display fdb entries, add new entries, append
entries, and delete old ones.
bridge fdb add - add a new fdb entry
This command creates a new fdb entry.
LLADDR the Ethernet MAC address.
dev DEV
the interface to which this address is associated.
self - the address is associated with a software fdb (default)
embedded - the address is associated with an offloaded fdb
router - the destination address is associated with a router.
Valid if the referenced device is a VXLAN type device and has
route shortcircuit enabled.
The next command line parameters apply only when the specified device
DEV is of type VXLAN.
dst IPADDR
the IP address of the destination VXLAN tunnel endpoint where
the Ethernet MAC ADDRESS resides.
vni VNI
the VXLAN VNI Network Identifier (or VXLAN Segment ID) to use to
connect to the remote VXLAN tunnel endpoint. If omitted the
value specified at vxlan device creation will be used.
port PORT
the UDP destination PORT number to use to connect to the remote
VXLAN tunnel endpoint. If omitted the default value is used.
via DEVICE
device name of the outgoing interface for the VXLAN device
driver to reach the remote VXLAN tunnel endpoint.
bridge fdb append - append a forwarding database entry
This command adds a new fdb entry with an already known LLADDR. Valid
only for multicast link layer addresses. The command adds support for
broadcast and multicast Ethernet MAC addresses. The Ethernet MAC
address is added multiple times into the forwarding database and the
vxlan device driver sends a copy of the data packet to each entry
found.
The arguments are the same as with bridge fdb add,
bridge fdb delete - delete a forwarding database entry
This command removes an existing fdb entry.
The arguments are the same as with bridge fdb add,
bridge fdb show - list forwarding entries.
This command displays the current forwarding table.
With the -statistics option, the command becomes verbose. It prints
out the last updated and last used time for each entry.
bridge mdb - multicast group database management
mdb objects contain known IP multicast group addresses on a link.
The corresponding commands display mdb entries, add new entries, and
delete old ones.
bridge mdb add - add a new multicast group database entry
This command creates a new mdb entry.
dev DEV
the interface where this group address is associated.
port PORT
the port whose link is known to have members of this multicast
group.
grp GROUP
the IP multicast group address whose members reside on the link
connected to the port.
permanent - the mdb entry is permanent
temp - the mdb entry is temporary (default)
bridge mdb delete - delete a multicast group database entry
This command removes an existing mdb entry.
The arguments are the same as with bridge mdb add.
bridge mdb show - list multicast group database entries
This command displays the current multicast group membership table. The
table is populated by IGMP and MLD snooping in the bridge driver auto-
matically. It can be altered by bridge mdb add and bridge mdb del com-
mands manually too.
dev DEV
the interface only whose entries should be listed. Default is to
list all bridge interfaces.
With the -details option, the command becomes verbose. It prints out
the ports known to have a connected router.
bridge vlan - VLAN filter list
vlan objects contain known VLAN IDs for a link.
The corresponding commands display vlan filter entries, add new
entries, and delete old ones.
bridge vlan add - add a new vlan filter entry
This command creates a new vlan filter entry.
dev NAME
the interface with which this vlan is associated.
vid VID
the VLAN ID that identifies the vlan.
pvid the vlan specified is to be considered a PVID at ingress. Any
untagged frames will be assigned to this VLAN.
untagged
the vlan specified is to be treated as untagged on egress.
self the vlan is configured on the specified physical device.
Required if the device is the bridge device.
master the vlan is configured on the software bridge (default).
bridge vlan delete - delete a forwarding database entry
This command removes an existing fdb entry.
The arguments are the same as with bridge vlan add. The pvid and
untagged flags are ignored.
bridge vlan show - list vlan configuration.
This command displays the current VLAN filter table.
bridge monitor - state monitoring
The bridge utility can monitor the state of devices and addresses con-
tinuously. This option has a slightly different format. Namely, the
monitor command is the first in the command line and then the object
list follows:
bridge monitor [ all | OBJECT-LIST ]
OBJECT-LIST is the list of object types that we want to monitor. It
may contain link, fdb, and mdb. If no file argument is given, bridge
opens RTNETLINK, listens on it and dumps state changes in the format
described in previous sections.
If a file name is given, it does not listen on RTNETLINK, but opens the
file containing RTNETLINK messages saved in binary format and dumps
them. Such a history file can be generated with the
NOTES
This command uses facilities added in Linux 3.0.
Although the forwarding table is maintained on a per-bridge device
basis the bridge device is not part of the syntax. This is a limitation
of the underlying netlink neighbour message protocol. When displaying
the forwarding table, entries for all bridges are displayed.
Add/delete/modify commands determine the underlying bridge device based
on the bridge to which the corresponding ethernet device is attached.
SEE ALSO
ip(8)
BUGS
Please direct bugreports and patches to: <netdev@vger.kernel.org>
AUTHOR
Original Manpage by Stephen Hemminger
iproute2 1 August 2012 BRIDGE(8)
Czas wygenerowania: 0.00054 sek.
Created with the man page lookup class by Andrew Collington.
Based on a C man page viewer by Vadim Pavlov
Unicode soft-hyphen fix (as used by RedHat) by Dan Edwards
Some optimisations by Eli Argon
Caching idea and code contribution by James Richardson
Copyright © 2003-2023 Linux.pl
Hosted by Hosting Linux.pl